Motorcycle rear swing arm axle

Krystian

Reliable opinion

Fits perfectly no problems with installation rear works flawlessly part made correctly as you can see in the attached photo recommend solid company

Szefunio

Reliable opinion

Ogar 200 88' These bushings are a real g#wno :) At first glance everything looks beautiful, seemingly nicely made. Problems began when trying to seat the bushing . It turned out that it was completely the wrong dimension. The sleeve got stuck, I had to scoop it quite aggressively risking damage to the paint coating. When I finished seating it turned out that... more

Wojtoo

Reliable opinion

Hello I bought control arm axles for my Stallion 200, of which I have 4 pieces. The axles fit my mopeds perfectly. The plastic bushings have an additional metal bushing inside which affects the handling of the moped. I rate the workmanship and aesthetics of the axles and bushings at 5+. They fit perfectly after dismantling the worn ones.

Bartosz

Reliable opinion

Romet Kadet. The axle of the control arm fits perfectly, when placing the bushings can be slightly assisted with tow, and their pressing on the vise or hammering with a hammer is carried out through a piece of board so as not to damage the bushing itself. The control arm after installing the new bushing and axle behaves smoothly and as desired.

Daniel

Reliable opinion

Simson s51 1984. The metal and rubber bushings fit the control arm perfectly, with a little oil goes in with your fingers, they sit securely without excessive play. The axle itself also fits very well, no problems with the installation of the kit. I am very pleased with this purchase as well as others at G-Moto

Mikołaj

Reliable opinion

Romet Ogar 205 50cm3 1987 To hammer the plastic bushings into the control arm you have to work a little hard (at the beginning I had a problem and had to grind a little in the middle of the control arm hole so that the bushing could enter into place fairly smoothly) but it was worth it, everything fits no backlash. I recommend, this product.

Kamil

Reliable opinion

The axle itself differs from the original, where the original one has a sort of made thickening on the axle, but nevertheless it fits and does not interfere with anything. The bushings are slightly different, but it also does not make any problems in installation. (Romet Ogar 200 50cm3)

Kacper

Reliable opinion

Well-made item, hard pre-everything, not like others you will bend this axle in your hands, bushings bdb. Made, simply and neatly together with rubbers As for the fit, bushings, rubbers and axle go in as if done with the head

Patryk

Reliable opinion

My motorcycle Romet Komar 2350 from the year 1975 I bought the control arm axle fit super, the product as described compared to other ads on other sites. The product I ordered fit like the original the same dimensions.

Adrian

Reliable opinion

I think that the product is worth recommending, the suspension works without any stress and play. The product is really made of good materials, of course, everything as well as delivery in a perfect way zosatatało sold.

Michał

Reliable opinion

I own a Romet Ogara 205.Some time ago I purchased this axle and I am pleasantly surprised!Installation mileage without any problems.It deviates a little from the original,but otherwise you can not see any difference.I highly recommend.

Bogusław

Reliable opinion

Romet Ogar 200. unfortunately the bushings did not fit perfectly, it was necessary to grind a little, but overall OK. I don't know if it's the fault of the bushings or the holes for them. I matched, put them on and it runs like gold.

Jakub

Reliable opinion

It is an axle from romeet 200 But it fits the same to cross KXD 125 everything fits it as well as rubbers and bushings and axle everything is refined at a high level to be perfect parameters

Kacper

Reliable opinion

The bushing is not suitable for anything there is too much slack, I recommend leaving the old one if it is suitable and put in a new axle or put in an axle with a larger diameter so that there is no slack, Komar 2351. regards.

Maciej

Reliable opinion

According to my assessment, the screw is too thin and hence there is a large clearance between the screw and the bushing . It has a dimension of 9.7 mm and should be 10.7 mm. With this dimension the clearance that should be there is correct.

Kamil

Reliable opinion

Hello, the product does not fit, you have to grind it to get the axle to enter I do not recommend the seller in a fairly ok but Chinese parts do not buy because here it's all badizewie and done to jerk off

Dawid

Reliable opinion

Romet ogar 200. year 86. very good workmanship control arm axle fits as it should zero backlash I recommend fast shipping very well protected package

Mateusz

Reliable opinion

The metal part of the bushing is some two small bushings not axially drilled making it very difficult to install. In the original, the bushing is one-piece.

Krzysztof

Reliable opinion

Romer ogar 205. very good axle , fits without any problem . There is no play on the rocker arm as it was before the overhaul . I am satisfied with my purchase

Adrian

Reliable opinion

The plastic bushings go nicely tight into the control arm, but the inner metal tubes that overlap the axle have more play than my previous one.